--- title: "Refrigerator error code DI SP / DISP" description: "Electrolux refrigerator error code DI SP / DISP: A cube is stuck in the chute and the door flap cannot close, so the alarm sounds." url: "https://electroluxmiami.support/error-codes/refrigerator-di-sp-disp/" date_modified: "2026-09-11" Appliance type: "Refrigerators" --- # Refrigerator error code DI SP / DISP ### What DI SP / DISP means on this make A cube is stuck in the chute and the door flap cannot close, so the alarm sounds. The maker names three causes and every one of them is about a bin that sat still: infrequent use, temperature swings, a power cut. Cubes that part-thaw and refreeze bond into a single mass around the auger, and the auger then either cannot turn or shears a piece off into the chute. It is the classic complaint of a second refrigerator and of a household that travels — and in a region with summer outages, it is the code that arrives the week after a storm. ### The other ways this one is printed DI SP / DISP · DISP · DI SP The same condition is printed differently on different panels of the same make, and every spelling the maker publishes for it is above. Whichever of them you searched for, this is the right page. ### Where this appears, and why not to clear it On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. ### What to do about it - Take the bin out completely, empty it, and let it thaw somewhere it can drain. Chipping at it in place is how augers get bent. - Dry the bin, refit it squarely, and check it seats fully home — a bin sitting proud jams against the maker at the back. - Look up into the chute with a torch for a piece still wedged, and clear it by hand rather than with the paddle. - Throw the first batch of new ice away and see whether it dispenses. If it jams again with fresh cubes, the auger, its motor or the flap is the visit. ### Where this goes next The job this usually becomes is [diagnostic visit](/services/diagnostic-visit/), and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 912-9018](tel:+13059129018) and describe what the panel is doing before booking anything. Indicates there is ice jammed in the chute. An alarm will sound when a cube is stuck in the chute too long. Ice has melted and frozen around the auger due to infrequent use, temperature fluctuations, and/or power outages. Ice cubes are jammed between the ice maker and the back of the ice bin. What this one means What DI SP / DISP means on this make A cube is stuck in the chute and the door flap cannot close, so the alarm sounds. The maker names three causes and every one of them is about a bin that sat still: infrequent use, temperature swings, a power cut. Cubes that part-thaw and refreeze bond into a single mass around the auger, and the auger then either cannot turn or shears a piece off into the chute. It is the classic complaint of a second refrigerator and of a household that travels — and in a region with summer outages, it is the code that arrives the week after a storm. The other ways this one is printed DI SP / DISP · DISP · DI SP The same condition is printed differently on different panels of the same make, and every spelling the maker publishes for it is above. Whichever of them you searched for, this is the right page. Where this appears, and why not to clear it On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. What to do about it Take the bin out completely, empty it, and let it thaw somewhere it can drain. Chipping at it in place is how augers get bent. Dry the bin, refit it squarely, and check it seats fully home — a bin sitting proud jams against the maker at the back. Look up into the chute with a torch for a piece still wedged, and clear it by hand rather than with the paddle. Throw the first batch of new ice away and see whether it dispenses. If it jams again with fresh cubes, the auger, its motor or the flap is the visit. Where this goes next The job this usually becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 912-9018](tel:+13059129018) and describe what the panel is doing before booking anything. --- **[Read full article: Refrigerator error code DI SP / DISP](https://electroluxmiami.support/error-codes/refrigerator-di-sp-disp/)**